Recommended Starting Settings for Film Cutting
For most materials, start with cutting pressure 300, cutting speed 200, blade holder scale 5, and material size 180 mm wide × 120 mm high. These are the intelligent film cutting machine’s de...
Search
Find an article
Showing 52 results for "Blade Holder Scale"
Choosing Blade Pressure for Different Screen Protector Materials
Blade pressure should be set according to the screen protector material. Regular back film generally requires 250–300, four-layer soft film 300–350, UV material 350–400, and explosion-proof...
Default Cutting Settings and Material-Specific Ranges
The basic default setup is a material size of 180 mm width × 120 mm height, cutting pressure of 300, cutting speed of 200, and blade holder scale of 5. These defaults are suitable for most m...
UV Material Cutting Parameters: Scale 6 and Pressure 380
The cutting parameter setting for UV material is the documented combination of blade holder scale 6 and cutting pressure 380 on the screen protector cutting machine. These two values define...
Stop Film Bulging by Correcting the Blade Setup
Film can bend or bulge during cutting when the blade holder is set too deep, the blade is worn out, or a non-original blade does not match the required angle and sharpness. Reduce the blade...
Recommended Starting Settings for Standard Back Film
The standard recommended setting for most back film cutting tasks is blade size 4 with pressure set to 300. The blade holder scale is not universal: it depends on the film’s thickness, and m...
Default Cutting Settings for Most Screen Protector Materials
For most cutting tasks, keep the machine’s default cutting speed at 200 and blade pressure at 300. These settings are suitable for the majority of screen protector materials, so they normall...
Replace a Loose Blade Carriage Holder Instead of Tightening It
If the main holder, also called the blade carriage holder, is loose and must be pressed by hand for the machine to cut properly, the holder is worn out or has lost stability. This precision...
Restore Blade-Holder Movement When the Car Still Travels
When the car moves after cutting starts but the blade holder does not drop, first verify the power adapter, cutting pressure, and cable connections. Use the original power adapter, increase...
Restore Proper Screen Protector Cutting in Three Stages
If the machine cannot cut screen protector materials properly, first replace both the blade and blade holder with new ones. Then set the cutting pressure to 300 and attempt the cut again. Fi...
0.45 mm PET Cutting Is Supported With Setting Adjustments
Yes, the screen protector machine can cut PET material with a thickness of 0.45 mm. However, successful use may require adjustments to the machine settings. The cutter scale can be adjusted...
Cutting Different Material Thicknesses Requires Scale Adjustment
Conditionally, yes: the screen protector cutting machine can cut materials of various thicknesses when the cutter scale is adjusted accordingly. The documented support does not specify a max...
Restore Blade-Down Operation by Replacing the Mainboard
If the blade does not drop properly during cutting, the most likely cause is a malfunctioning mainboard. The blade-down action depends on the Y-axis motor signal sent by the mainboard. When...
A Baseline Configuration for Screen Protector Cutting
If you are having trouble configuring the machine, try a speed of 200, pressure of 300, blade holder scale of 5, material width of 180, and material height of 120. Enable Auto Loading and di...
Use 180 × 120 mm for Most Mobile Screen Protector Cuts
For mobile phone screen protectors, use the default paper or material size of 180 mm width × 120 mm height. This size is suitable for most cutting needs, so it can generally remain unchanged...
This Screen Protector Machine Uses Physical Cutting, Not Laser
No. This screen protector cutting machine is not a laser cutting machine. It uses physical cutting with a blade. The documented benefits of this cutting method are safe operation, no cutting...
Aligning Images for Standard Film and Custom Prints
The correct image alignment setup depends on the material you are using. For standard back film, enter the material’s actual size in settings and enable “Center Cutting” on the cutting page....
Replace a Scratched M188 Rubber Strip When Cutting Becomes Uneven
Replace the rubber strip in the MTB-CUT M188 when its surface is scratched and screen protector cutting becomes inconsistent. A damaged strip can result in some areas being cut through while...
How to Operate the MTB-CUT 180TPro Before You Order
The MTB-CUT 180TPro is operated through its 7-inch color touchscreen or a connected Android app: the operator finds the required device model, prepares and loads the appropriate film, sends...
How Should Buyers Validate the MTB-CUT 180T Before Ordering?
Buyers should validate the MTB-CUT 180T with representative film materials and real device patterns before approving an order. Its stated material support and adjustable cutting controls mak...